Dove Lifts Header
Elevator Energy Costs in Nigeria: How to Cut Your Bill Without Replacing the Lift

Introduction

On a Band A tariff, electricity is one of the largest operating costs in any Lagos commercial building. Facility managers scrutinise air conditioning, lighting, and generators. The elevator often escapes the same level of attention — because its consumption is less visible, and because nobody has broken the numbers down for them.

That is a mistake worth correcting. A lift that runs continuously through a working day, carrying passengers up and down, consumes meaningful electricity. On an older installation with a resistance‑based starting system and incandescent car lighting, the consumption can be several times higher than a modern equivalent.

The good news: most of the savings are available without replacing the elevator. Drive upgrades, lighting changes, and control settings deliver substantial reductions on the existing installation.

This guide explains what actually drives elevator energy consumption in Nigeria, what the upgrades save, and how to prioritise them.

Hard fact: The single largest energy consumer in a conventional elevator is the drive system during acceleration and deceleration. Older resistance‑based starting systems dissipate energy as heat during every start, while VVVF drives control motor speed electronically and avoid that loss entirely.


Where Elevator Electricity Actually Goes

Before upgrading anything, understand the consumption profile. An elevator's electricity use divides into four categories.

The drive and motor. This dominates. Every trip involves accelerating the car and counterweight, running at speed, then decelerating. Old systems waste energy as heat during acceleration through resistor banks. Modern VVVF drives control the motor electronically and recover or avoid much of that loss.

Standby consumption. The controller, car lighting, ventilation fan, and landing displays draw power continuously — even when the lift sits idle overnight. In a building where the lift runs eight hours and sits idle sixteen, standby consumption is a significant share of the total.

Car lighting and ventilation. Incandescent or halogen car lighting draws far more than LED equivalents. A continuously running car fan adds to the total. Both run whether or not anyone is inside.

Machine room cooling. A machine room without adequate ventilation requires air conditioning to protect the controller and drive from heat. That air conditioning is often counted as building load rather than elevator load — but it exists because of the elevator.

Hard fact: Standby consumption in a lift with incandescent car lighting and a continuously running fan can represent a large share of total annual elevator electricity use, particularly in buildings with short operating hours.

For context on how these components behave in a Nigerian installation, our guide on MRL elevator maintenance problems in Nigeria covers heat and ventilation issues that also drive consumption.

Bridge: With the consumption profile clear, the upgrades that address each category become obvious.


The Upgrades That Deliver Real Savings

Not every energy upgrade is worth the investment. These are the ones that consistently pay back.

VVVF drive retrofit. This is the highest‑impact upgrade available on an existing lift. Replacing a resistance‑based starting system with a VVVF drive eliminates the energy wasted as heat during every acceleration, and produces smoother, quieter operation as a side benefit. The saving is substantial and applies to every single trip.

LED car lighting. A straightforward replacement. LED car lighting draws a fraction of the power of incandescent or halogen equivalents, and lasts far longer. The payback is rapid because car lighting runs continuously.

Standby mode and auto‑shutoff. Modern controllers can be configured to switch off car lighting and the ventilation fan after a period of inactivity, reactivating on the next call. This eliminates most of the overnight standby waste. It is a controller setting, not a hardware replacement — sometimes available on existing installations.

Regenerative drive. A regenerative drive captures energy during deceleration and braking and feeds it back into the building supply, rather than dissipating it as heat. On lifts with high travel and heavy traffic, the recovery is meaningful.

Ventilation instead of air conditioning. Where the machine room runs an air conditioner to keep the controller cool, a properly designed ventilation system with filtered airflow can achieve the same protection at far lower running cost.

Hard fact: Regenerative drives recover energy during the descent of a loaded car and the ascent of an empty one — the two conditions where the motor is effectively generating. On high‑rise, high‑traffic lifts, the recovered energy reduces net consumption noticeably.

Bridge: Regenerative drives deserve a closer look, because they are frequently misunderstood in the Nigerian context.


Regenerative Drives in Nigeria: What They Can and Cannot Do

Regenerative drives are widely promoted as an energy‑saving feature. In Nigeria, the benefit is real but different from what the marketing suggests.

What regeneration does: during deceleration, and during travel in the direction where the load is driving the motor, the motor acts as a generator. The regenerative drive converts that energy and either returns it to the building supply or dissipates it through a resistor.

What it cannot do in Nigeria: feed power back to the utility grid for credit. Net metering for elevators does not exist in the Nigerian market. So the "sell power back" framing does not apply here.

What it does do in Nigeria: reduces the net electricity drawn from the building supply. Instead of consuming full power during every phase of travel, the lift recovers energy during the phases where the load is driving the motor. The net consumption drops.

Where the benefit is greatest: high‑rise buildings with long travel distances and heavy traffic — office towers, hotels with significant guest movement, hospitals with constant bed and staff transport. In a low‑rise building with short trips, the benefit is smaller and the premium may not justify itself.

Hard fact: Regenerative drives reduce energy consumption and heat generation in the machine room. The reduced heat also lowers machine room cooling requirements — an additional saving that is often overlooked.

Bridge: With the technical options clear, the practical question is how to sequence the work.


How to Prioritise Your Energy Upgrades

Budget is always finite. This is the order that delivers the most saving per naira spent.

Priority 1: Controller settings. Before spending on hardware, check whether your existing controller supports standby mode and auto‑shutoff. If it does, configuring it costs very little and eliminates overnight waste immediately.

Priority 2: LED car lighting. Inexpensive, quick to install, and reduces a continuously running load. Payback is rapid.

Priority 3: VVVF drive. The largest saving available on older lifts. This is usually the point where the investment becomes meaningful — the drive upgrade typically pays back through reduced electricity consumption over a defined period, and delivers smoother operation as a secondary benefit.

Priority 4: Regenerative drive. Worth the premium on high‑rise, high‑traffic installations. On low‑rise buildings, evaluate carefully before committing.

Priority 5: Machine room ventilation redesign. If your machine room runs air conditioning year‑round, a ventilation upgrade may reduce that load at modest cost.

What to avoid: upgrading the drive without addressing the door system and lighting, or investing in regeneration on a building with low travel and light traffic. The savings do not justify the cost in those cases.

Hard fact: A VVVF drive upgrade reduces both energy consumption and mechanical wear, because the motor no longer experiences the abrupt acceleration and deceleration of resistance‑based starting. The maintenance benefit adds to the energy benefit.

For how these upgrades fit into a wider programme, our guide on elevator modernization in Lagos explains how drive and controller replacement sit within a full modernization scope.

Bridge: Measuring the saving is the part most building owners skip — and it is the part that proves the investment.


Measuring the Saving: How to Prove It Worked

An energy upgrade without measurement is an act of faith. With measurement, it becomes a documented cost reduction.

Install a sub‑meter. A dedicated electricity meter on the elevator supply separates lift consumption from building load. Without it, you cannot know what the lift consumes or what the upgrade saved.

Record a baseline. Before any upgrade, log consumption over a representative period — ideally several weeks including both busy and quiet days. This is your comparison point.

Record after the upgrade. Continue logging over the same period length and comparable usage. Compare.

Calculate the payback. Take the reduction in monthly consumption, multiply by your tariff, and compare against the upgrade cost. This gives you the payback period in months.

Why this matters beyond the accounting: documented energy savings support green building certification submissions, strengthen the case for further upgrades, and provide defensible figures if the building is being valued or sold.

Hard fact: Green building certification schemes including EDGE and LEED require documented energy performance. Elevator energy savings contribute to the building's overall submission only if they are measured and recorded — not estimated.

For buildings pursuing certification, our guide on reduce elevator energy bills in Nigeria covers the documentation side in more detail.

Bridge: Here are the questions facility managers ask us most often.


Frequently Asked Questions

How much electricity does an elevator use in Nigeria?

It depends on the lift type, drive system, travel height, traffic volume, and lighting. A hydraulic lift typically consumes more than a traction lift for the same duty. An old resistance‑start traction lift consumes more than a modern VVVF unit. The only reliable figure is the one from your own sub‑meter.

What is the single biggest energy saving available on an existing lift?

For most older installations, a VVVF drive retrofit. It eliminates the energy wasted during acceleration on every single trip, and delivers smoother operation as a secondary benefit.

Do regenerative drives work in Nigeria without net metering?

Yes, but differently from how they are often marketed. They reduce net consumption from the building supply rather than exporting power to the grid. The saving is real; the "sell power back" framing is not applicable here.

How long does a VVVF drive upgrade take?

The drive and controller work is typically completed within a short programme, but the lift is out of service during that period. In buildings with multiple lifts, units are upgraded sequentially so circulation continues.

Will an energy upgrade affect my maintenance costs?

Usually it reduces them. VVVF drives eliminate the abrupt mechanical stress of resistance‑based starting, which reduces wear on the machine, brake, and door system. Smoother operation means fewer repairs over the asset's life.

Can I upgrade an old lift without a full modernization?

Yes. Drive, lighting, and controller settings can be upgraded independently of the door system, fixtures, and safety devices. This allows savings to be captured on a staged basis. However, if the lift also lacks an ARD or has worn safety devices, those should be addressed in the same programme for compliance reasons.

How do I know what my elevator currently consumes?

Install a dedicated sub‑meter on the elevator supply and log consumption over several weeks. Without this baseline, you cannot measure the effect of any upgrade. We can advise on sub‑meter installation during a site survey.

Hard fact: Elevator energy consumption cannot be reliably estimated from the motor nameplate rating alone. Actual consumption depends on traffic volume, travel distance, load conditions, and standby behaviour — which is why measurement is the starting point, not the conclusion.


Want to Know What Your Lift Is Actually Costing You?

Most buildings have never measured their elevator's electricity consumption. They know the total bill but not the split — and therefore cannot tell whether an upgrade would pay for itself.

We can help you find out. We will review your lift type, drive system, lighting, and control settings, advise on sub‑metering, and tell you which upgrades would deliver a measurable saving on your specific installation. Where the existing controller already supports standby mode, we will configure it as a first step at minimal cost.

We do not publish fixed figures for drive retrofits or energy assessments, because scope varies by lift type, capacity, and travel. What we can do is assess your installation and give you a written proposal showing the scope, the expected saving, and the payback calculation.

Send us your lift details — type, age, number of stops, and your current electricity tariff band. We will tell you where the savings actually are.

👉 Speak to Dove Lifts about elevator energy costs


Dove Lifts — Traction, MRL, and hydraulic elevator installation, modernization, and maintenance across Nigeria and West Africa. VVVF drive retrofits, LED upgrades, and documented energy savings.

Leave a Reply

Your email address will not be published. Required fields are marked *